What is the installation sequence and method of the prefab house?

What is the installation sequence and method of the prefab house?

Prefab house installation is similar to high-rise buildings. The foundations of nearby and partition walls should be leveled. Reinforced concrete is best used, then struts are used to connect the skeleton to the beams, upper partitions, exterior wall panels, and door and window frames; next lay the floor, then one level up, then install the roof trusses and house panels, and finally install the doors and windows, etc. , and pull the vertical support. There are sanitary ware, small hardware, etc. So, what is the installation sequence and method of the prefab house? Let's take a look at the editor of the container house!

Preliminary steps of the prefab house:

1. Trenching;

2. Foundation, there are brick foundation and concrete foundation;

3. Steel frame device;

4. If it is multi-storey, please install prefabricated floor slabs;

5. Color steel plate device;

6. The first floor;

5. Door and window equipment;

6. Interior decoration;

Prefab house installation steps:

first step:

Allow the building foundation to dry for at least 3 days before starting to build thick house walls, according to the prefab house foundation construction drawings. Place the ground beams close to the inside of the double line in the plan and connect them with blast bolts and establish struts at each joint corner of the ground beams. Note: Double angled holes are built into both ends of the gable of the flat house.

Step 2:

Assemble the floor on the ground according to the various views of the construction drawing, riveted on the aluminum floor buckle with 5.2 rivets at the bottom, remember to cut the position of the doors and windows according to the direction of the construction drawing, and riveted it on the aluminum frame, PLEASE NOTE: Don't rive between the panels first, lay and assemble first to fix the door and window position and rive the door and window aluminum frame.

third step:

Assemble the assembled boards one by one in each direction according to the floor plan of the board room. The board is riveted with rivets, the outer corners are riveted with arc aluminum, and the inner corners are riveted with angle aluminum. riveted.

the fourth step:

According to the distribution map of the large wave tiles in the construction drawing of the prefab house, place the large wave tiles on the above completed entities one by one, and connect them with 75 self-tapping screws.

the fifth step:

Rivet the tiles on the ridge of the movable panel house, connect the gable to the gable, and connect the front and rear eaves to the sink, both riveted with rivets. (The flat roof type has no ridges and roof tiles.) Finally, apply glazing glue to every gap and rivet in the plank roof, then apply glazing glue to the exterior walls and gaps near the windows

The concealed project of prefab house means that in the construction process, after the completion of the previous process, it will be covered in the next process, and all parts that cannot be inspected should be decorated in the room after completion. 'Concealed engineering' is the key, if the 'concealed engineering' is not done well, no matter how beautiful it looks, it will be futile.

'Concealed works' can be divided into hydraulic installations, electrical installations, and moisture and waterproof works. Every item in the process cannot be ignored. If there is any doubt, it may cause serious economic loss and even endanger personal safety. Determine the construction techniques and materials of waterproofing works to prevent unnecessary economic losses and injuries.

The above is the whole content of 'Installation sequence and method of prefab house?' If you have any questions about container houses and residential container houses, please consult the online customer service of container houses, or call directly for consultation!

prefab house manufacturers are required in the manufacture of almost every product and prefab homes prefab houses is one of the most common machines.

Energetic, optimistic entrepreneurs often tend to believe that sales growth will take care of everything, that Lida Group will be able to fund our own growth by generating profits.

Lida Group understands how essential it is to offer ample options, such as prefab housescontainer frame to afford high-quality products for customers.

Lida Group harnesses science and technology to create products that support safer and healthier living and that enhance the overall quality of life.